How to Re-seal an uPVC Window

Re-seal an uPVC WindowIf you are looking for the best way in order for you to reseal your upvc window, you must be able to understand the concept in its entirety. The popularity of this type of window is due to the fact that the calls for green and environmentally friendly houses are actually very popular right now. For example, a lot of materials in the market today are actually supposed to pass environmental standards in order for it to be patronized by different lobby groups. Thus, people have made the need to actually strike a balance between the aesthetic value of their house as well as its ability to respond to the growing trend of deep green environmentalism. (more…)

Tags: , , , , , , , , , , , , , ,

How To Fix uPVC Doors That Let In Rain At The Bottom?

uPVC doors sweepUnplasticized polyvinyl chloride, or UPVC, does not contain the chemicals that soften standard PVC. UPVC doors are very popular with homeowners because of the advantages they offer over traditional wooden doors. They can be caste, which eliminates the need for hand tooling. They are not attacked by termites and do not require painting. They come in many different styles and door types, such as bi-folding doors, patio doors, and decorative entrance doors. UPVC provides much higher insulation value than wood; it does not split from sun damage, nor does it warp from exposure to ambient moisture.

A properly installed UPVC door requires very little maintenance. However, an improperly installed door can leak and allow rainwater to enter along the bottom of the door. There are several ways to address this problem.

For UPVC doors with adjustable sills:

(1) Open the door and look down at the bottom of the doorframe. That bottom piece is the sill. It may have a piece of metal covering it, known as the sill plate. If the sill plate has a series of inset screws running longitudinally across the middle, then it is adjustable.

(2) These screws pass through the sill and contact the floor support beneath the doorframe. Loosening the screws will retract them up into the sill, allowing it to sag downward rest flush against the floor support. Tightening a screw causes it to extend further through the sill plate and push against the floor support. This will cause the sill to bow upwards slightly as the screw pushes it away from the floor. Slightly tightening all of the screws will raise the sill in a level manner.

(3) If rainwater is seeping under the door, you may be able to tighten the screws to lift the sill plate. If the sill lifts enough to contact the rubber gasket attached to the bottom of the door, then it creates a weatherproof seal.

For UPVC doors without adjustable sills:

(1) Remove the hinge pins and lift the door from the frame.

(2) Look along the bottom edge of the door. You should see a rubber gasket. It usually fits into a groove along the bottom edge of the door. This gasket is the door sweep. When the door closes, the door sweep creates a seal against the sill plate.

(3) Purchase a replacement door sweep at your local hardware store.

(4) Slide the new door sweep into the slot. It may need trimmed to the width of the door.

(5) Carefully place the door into the hinges and replace the hinge pins.

(6) Close the door and check the fit. The sweep must contact the sill plate as the door closes to create a weather tight seal.

For UPVC doors without sweeps:

(1) All doors must have a sweep in order to seal against the weather. If the door sweep is missing, purchase a replacement sweep at the local hardware store and install it. Each type of door sweep will have specific installation instructions.

Tags: , , , , , , , , , , , , ,

How to Install uPVC Windows

Installing uPVC windowsUPVC windows have been around since the 1970s. Since their creation, they have been used in almost every household. This type of window is also known as vinyl sliding or vinyl windows and they have are known to be more superior to timber window frames. However, there have been issues concerning its safety with regards to environment conservation. In spite of this, a lot of people are still interested in installing UPVC window frames in their homes as it is relatively more cost efficient than the other typical window materials that have been known to homeowners and builders.

One of the reasons why a lot are looking to install UPVC windows is that aside from helping to save money, it is also a good insulator. Unlike the common timber frame windows, UPVC is able to keep and maintain the heat inside the house especially during the winter season. It will generally improve the insulation in your house and compared to timber frames that are infamous for its poor heat maintenance, it would provide you with better warmth and comfort during the cold seasons. UPVC has high thermal resistance which refrains heat from going out the house.

Aside from this benefit, UPVC windows are very stable. It would not change in shape, texture, state, or appearance when the season changes. You must have noticed how your regular window frames would shrink during the dry, warm, and hot seasons and swell once the cold seasons come in. This might sound harmless but it actually poses risk and compromises the security for your home against breakage and burglary. Regular timber window frames also require more maintenance than the UPVC. You would need to repaint timber window frames to keep it from rotting and you would also need to apply wood putty treatment. More or less, the UPVC could stay as is for a long time once it is installed. If you now wish to have UPVC installed in your own home, read on for the steps on how you can install UPVC windows yourself.

INSTALLING UPVC WINDOWS

STEP 1: The first step in installing UPVC window frames is to measure the interior part of the window opening where you will install the UPVC before purchasing the UPVC vinyl. This will ensure that the vinyl slide you will purchase is of accurate measurement. You should take note that the opening should be a bit wider and higher than the new window that is set to be installed.

STEP 2: Next, you can now start removing the existing window glass fixture to be replaced by the UPVC. Follow safety precautions especially if you are dealing with glass. It is best if you can work from the inside of the house and see to it that you dispose off the glass with full care. It is also recommended that you keep the inside stop which could be reused.

STEP 3: Next on the step’s list is to seal the nail fin which is efficient in preventing water leakage.

STEP 4: The next part is the installation of the UPVC. Push it towards the opening while making sure that it is in the correct positioning. Use screws that are normally included in UPVC packages or those that you would need to purchase separately. If you followed the recommendation of keeping the inside stop, you can now use and reinstall it.

STEP 5: The final step in UPVC windows installation is caulking or sealing around the frame. You can use a water-based foam sealant or some butyl rubber.

 

Tags: , , , , , , , , , , , , , ,

How to Improve the Security of uPVC Windows

uPVC Window SecuritySecurity has become an even bigger concern these days, given the increase in crime rates. Even homes, which have previously been considered as a person’s safety zone, is no longer secure anymore housebreaking has become so commonplace that people barely bat their eyelashes when they hear news about a malicious individual breaking in someone’s home. What people may not be aware of is that break-ins are crimes of opportunity: thieves and robbers are constantly on the lookout for weak spots in a person’s home and are able to enter a house because of these. More often than not, windows are the weak spots of a house. Even if these are closed, the glass can easily be broken or the panes jimmied to grant thieves access to your home. If you want to provide more security for your home, consider installing uPVC windows. (more…)

Tags: , , , , , , , , , , , , , , ,

Are uPVC Windows and Doors Fire Resistant?

Fire Resistant uPVC Windows and DoorsIn an era where state-of-the-art technological innovation is king, UPVC windows and doors are the best choice when it comes to home improvement. This is not surprising though. Apart from the fact that UPVC windows and doors are very easy to assemble, they are durable and cheap too. Home-builders with discriminating taste in terms of material and aesthetics, will surely be glad to find out that doors and windows made from UPVC are also available in an assortment of sizes, colors, and designs. UPVC doors and windows also have different specifications specifically designed to suit your needs. Choose from a variety of specifications such as French windows, tilt n’ turn windows, bow or bay windows, stable doors, composite doors, residential doors, patio doors, and many more.

However, there are some important consideration before choosing the right UPVC windows and doors for your home. In choosing a UPVC window, for instance, make sure that its material is durable, double-glaze, and of course, cost-effective. With the right kind of UPVC window, the thermal capacity of your living space will dramatically improve. This means that you and your family can benefit more from the windows’ high heat-resistance. In technical terms, resistance to heat is referred to as R-value. When looking for a UPVC window, you should therefore look for those with the highest R-value. The bottomline is, you should go for UPVC windows that are capable of maximum insulation.

The considerations in choosing the best UPVC windows are the same criteria that you should use in getting the right UPVC doors. Aside from choosing a UPVC door that combines elegance, style, and durability, make sure that the one that you will choose have properties that are capable of providing optimum insulation and thermal capacity. A low U-factor and a high R-value is an essential quality that you should look for. In fact, whether you are looking for a doors or windows made of UPVC material, make sure that they are highly fire-proof.

In case you did not know, there are excellent UPVC windows and doors that are made from the best fire-proof materials. Since windows and doors tend to be your primary escape route during incidents such as fire, it is best to choose ones that are durable and made of excellent heat resistant materials. UPVC windows and doors are also self-extinguishing. This makes them effective in minimizing fire-related incidents due to extreme heat especially during the summer season.

Tags: , , , , , , , , , , ,

Next Page »